Subscribe via RSS Feed

Tag: "high-voltage"

Mechanical Answer to Stray Voltage

Mechanical Answer to Stray Voltage

[ 1 ] By  |  July 22, 2010  |  IAEI July-August 2010

Tenants of the Time & Life Building in New York’s Rockefeller Center include Time Inc., publisher of more than 100 magazines. In an effort to “green” the building, shaft grounding rings have been installed to protect the bearings of HVAC fan motors. Proper tuning of a variable frequency drive’s output range and proper grounding of [...]

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)
Photo 1

Stray Voltage — Catching What We Cannot See

[ 3 ] By  |  March 12, 2010  |  IAEI March-April 2010

“Where the cow won’t give milk anymore” is a standard lyric in old classic country songs; perhaps you’ve wondered why. Well, back in the early days many strange and downright bizarre occurrences happened on the farm, most of which were thought to be the product of superstition, bad living or old wives’ tales; but that [...]

1 Star2 Stars3 Stars4 Stars5 Stars (6 votes, average: 2.50 out of 5)

Rule 36-110, High Voltage Clearances

[ 0 ] By  |  January 14, 2006  |  IAEI January-February 2006

Both the Canadian Electrical Code (CE Code) Part I and Part III provide requirements for minimum horizontal clearances between high voltage lines and buildings, and vertical clearances between high voltage lines and grade. This article discusses the different approach taken by each. The Canadian Electrical Code, Rule 36-110 makes reference to Table 33, which provides [...]

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)

Maximum Circuit Voltages

[ 0 ] By  |  January 27, 2004  |  IAEI January-February 2004

The Canadian Electrical Code in some instances limits maximum applied voltages to protect the general public and inexperienced people from electrical shock hazards. Unqualified persons are at greater risk due to their inability to identify electrical hazards and understand electrical shock risks. This article reviews some of the circumstances where the code prescribes maximum voltages [...]

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)
Photo 1. Glass sleeve

Clearances for Exposed GTO Cables and Terminations

[ 0 ] By  |  July 4, 2002  |  IAEI July-August 2002

There have been numerous inquiries to my office about the requirement of increased clearances for combustible sleeving and electrode boots from conductive and combustible materials, (which equates to everything) when used with high voltage GTO cables and terminations. The growing necessity to increase the clearance requirements has brought changes to Section 34 (high voltage sign [...]

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)

High Voltage Electrical Facilities that are Completely Safe

[ 0 ] By  |  January 11, 2002  |  IAEI January-February 2002

There are hundreds of customers in my company’s service area who own their own high voltage transmission, distribution and/or substation electric supply facilities. The service voltages for these customers range from 4 kV to 138 kV. Many years ago, I investigated an accident involving the death of a farmer on one such facility. The farmer [...]

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)
Photo 1. A case where the power cable entry point and termination is below the vent for the fuse

The NEC and Installations Over 600 Volts

[ 0 ] By  |  May 15, 2001  |  IAEI May-June 2001

The March/April issue of the IAEI News had an article on high voltage Equipment that discussed the new areas of application. The article discussed how these systems have evolved into some non-traditional areas along with some of the safety concerns for those working around this equipment. Codes and standards were discussed in general along with [...]

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)
Photo 1

Over 600 Volts

[ 0 ] By  |  March 15, 2001  |  IAEI March-April 2001

An inspector’s first look at the service shown above seems to show a relatively simple 120/240-volt single-phase service. It seems to include a service entrance riser, a service entrance wireway, and four 200-ampere fused disconnects, fused at 150 amperes. Disconnects are marked “Suitable for Use as Service Equipment.” Each disconnect has a tap to the [...]

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)
Photo 1. Privately owned combination cycle generation facility

“High Voltage” Systems and Safety

[ 0 ] By  |  March 15, 2001  |  IAEI March-April 2001

Most people in the non-utility side of the electrical industry are very familiar with the design, installation and inspection of electrical systems rated 600 volts or less; primarily because these systems are numerous, and these people work with them daily. The one exception is the sign industry where higher voltages are used primarily for neon [...]

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)

Working in Dangerous Proximity to Overhead High Voltage Lines – OSHA, NESC, and the Law

[ 0 ] By  |  March 17, 2000  |  IAEI March-April 2000

There are two sets of rules for work in proximity of overhead high voltage lines: The rules for qualified persons and the rules for unqualified persons. There is no gray area. Occupational Safety and Health Administration (OSHA) regulation 29CFR1910.269(x) defines a qualified person as “one knowledgeable in the construction and operation of the electric power [...]

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)

Bad Behavior has blocked 2662 access attempts in the last 7 days.